利用微气泡减小平板摩擦阻力的数值模拟

假定气-液两相流体均匀混合且微气泡在水流中存在滑移运动,运用混合多相流模型对水中运动平板的微气泡减阻过程进行了数值计算,研究了微气泡流的减阻机理,分析了主流速度及气体流量率等对减阻率的影响规律,同时构建了一个减阻率预报数学模型,并指出在微气泡减阻中存在一个与主流速度相对应的饱和气流量.     

水下近场非接触爆炸载荷作用下加筋板毁伤变形的数值仿真研究

采用高动态非线性有限元程序MSC.Dytran对复杂加筋板结构在水下爆炸载荷下的动态响应和变形模式进行了仿真分析和模型试验,建立了复杂加筋板架结构水下爆炸作用下动态响应的有限元计算方法.研究了加筋板在水下爆炸载荷下的不同毁伤形式,并利用有限元程序对复杂毁伤形式进行了瞬态毁伤过程分析,认为一定药量近距离爆炸时局部破坏要先于整体破坏.     

Analysis of the stress wave and rarefaction wave produced by hypervelocity impact of sphere onto thin plate

Shock wave is emitted into the plate and sphere when a sphere hypervelocity impacts onto a thin plate. The fragmentation and phase change of the material caused by the propagation and unloading of shock wave could result in the formation of debris cloud eventually. Propagation models are deduced based on one-dimensional shock wave theory and the geometry of sphere, which uses elliptic equations (corresponding to ellipsoid equations in physical space) to describe the propagation of shock wave and the rarefaction wave. The “Effective thickness” is defined as the critical plate thickness that ensures the rarefaction wave overtake the shock wave at the back of the sphere. The “Effective thickness” is directly related to the form of the debris cloud. The relation of the “Effective thickness” and the “Optimum thickness” is also discussed. The impacts of Al spheres onto Al plates are simulated within SPH to verify the propagation models and associated theories. The results show that the wave fronts predicted by the propagation models are closer to the simulation result at higher impact velocity. The curvatures of the wave fronts decrease with the increase of impact velocities. The predicted “Effective thickness” is consistent with the simulation results. The analysis about the shock wave propagation and unloading in this paper can provide a new sight and inspiration for the quantitative study of hypervelocity impact and space debris protection.     

超声冲击处理改善22SiMn2TiB装甲钢抗应力腐蚀性能研究

采用超声冲击处理工艺对22SiMn2TiB装甲钢试样进行了表面冲击强化,采用四点弯曲加载装置将处理和未处理的试样在3.5%NaCl溶液中进行了150 d的应力腐蚀试验。用X射线应力测定仪测定了应力腐蚀试验前试样表面的残余应力,用扫描电镜和透射电镜观察了处理后试样的断面组织。分析了超声冲击处理引起的残余应力和断面组织变化对改善装甲钢抗应力腐蚀性能的作用。结果表明,超声冲击处理引入的残余压应力和表层晶粒细化可以大大提高22SiMn2TiB装甲钢的抗应力腐蚀性能。     

917低磁钢与铝合金爆炸焊接复合实验研究

采用异种金属爆炸焊接复合技术 ,研制了 91 7低磁钢与LF5、LF2 1、LF1 1等铝合金的爆炸焊接复合板 ,并对该铝—钢复合板力学性能进行了实验研究 ,对复合界面进行了金相分析 .实验结果表明 ,该铝—钢复合板复合界面物理结合良好 ,其抗剪和抗弯强度满足实船使用要求     

Kelvin模型阻尼层合板的振动分析

基于Kelvin模型粘弹性材料本构关系导出了阻尼层合板的动力学微分方程组,给出了四边简支阻尼层合板的固有频率和损耗因子的解析解。与文献结果比较表明,将Kelvin模型应用于粘弹结构的动力特性问题求解,计算模型简便,且计算结果比常复数模型更为精确。分析了阻尼层参数变化对结构振动特性的影响。分析结果表明:增加阻尼层厚度,可以有效提高结构损耗因子;增加阻尼层材料的剪切模量,结构损耗因子增大到一定值后又逐渐减小,在减振设计中阻尼层的模量存在最佳值。     

LaB6空心阴极中毒特性

LaB_6阴极与其他类型阴极相比具有电子发射电流密度大等优点,已广泛用于电推进、高发射密度电子枪等产品。为了研究LaB_6空心阴极中毒特性、识别LaB_6空心阴极主要失效模式,分别对LaB_6空心阴极暴露大气后性能变化特征和引起性能变化的原因进行了研究。结果表明:LaB_6空心阴极在暴露大气后表面吸附大量中毒气体,出现了发射体表面逸出功增加、发射体短期中毒现象。此时空心阴极的放电电压和阴极顶温度均有所上升,经过短期工作后放电电压和阴极顶温度均恢复初始状态。但LaB_6空心阴极严重中毒后,并不能通过加热和离子轰击方式去除表面生成的氧化物。因此,可以在实验过程中通过监测空心阴极的阴极顶温度和阳极电压变化间接表征空心阴极发射体状态。     

The Early Responses of Air-backed plate subjected to underwater explosion with aluminized explosives

This work aims to research the effects on the early responses of the air-backed plate subjected to the loading generated by the underwater explosion with aluminized explosives. The loading characteristics of underwater explosion for ideal explosive (TNT), aluminized explosives (RS211 and RBUL) are obtained experimentally. The tested aluminized explosives have different energy output compared with TNT. Based on the Taylor plate theory, the early responses of the air-backed steel plate affected by the measured loading is analyzed. The analytical results indicate that the pressure curve of the shock wave within 1 time decay constant is the main factor affecting the kick-off velocity of the plate when cavitation occurring. The velocity responses of the plate produced by the loading of RS211 and RBUL are obviously different with that of an equivalent TNT charge, which also indicates validity and suitability should be noticed in the case of substituting TNT for aluminized explosives. Moreover, the uncertainties in the responses of the plate produced by RS211 and RBUL are much larger than TNT.     

基于表层及芯材阻尼特性的夹层结构导纳分析

针对复合材料夹层板结构,综合开展芯材材料阻尼特性动力学热分析(DMTA)试验、表层玻璃钢和芯材试件阻尼衰减特性研究,通过夹层板结构的模态激振试验得到结构的模态阻尼比。从结构动力学方程出发探讨了影响多自由度系统结构传递导纳的相关参量,试验对比分析了钢质板和复合材料夹层板两型结构的传递导纳特性,并研究了激振点与响应点间距对复合材料夹层结构传递导纳的影响。研究表明:当尺寸和边界条件相同时,影响结构传递导纳的主要因素是结构的固有频率和模态阻尼。试验还得到了复合材料夹层板较钢质板的基频提高值和传递导纳降低均值,该试验结果可为工程设计提供参考。     

加筋板在横向撞击下的吸能特性研究

运用非线性有限元分析方法,对不同撞击工况下加筋板的碰撞损伤过程进行了分析。加筋板结构采用理想弹塑性的材料模型,不计入应变率对材料强化的影响,在忽略接触面的摩擦等因素影响的前提下,考虑加筋板结构在刚性体碰撞下的变形过程,从而探讨加筋板结构的动态响应特点。研究结果表明,加筋板的吸能特性与撞击因素有一定的关系。非线性动态计算采用MSC/DYTRAN程序完成。